(531) 228-4688
Worker on a porch roof beside gray lap siding on a two-story house

Omaha Plains Siding: Omaha, NE Siding Repair and Replacement

Omaha Plains Siding repairs and replaces siding on Omaha, NE homes, from one cracked vinyl panel to a full tear-off. Re-siding a 2,000 sq ft home in vinyl typically runs $6,800 to $20,400. The bid you get counts the wall in squares and names the tear-off, the house wrap and the trim as their own lines.

Request a quote

One cracked panel or a house that needs it all? Say which, and which side of the house, and you hear a rough range by phone.

What you type goes only to the siding crew who would look at the house. Nobody else sees it, and nobody sells it.

In this area, about 60% of the homes were built before 1980. A lot of the times when you're needing new siding, there can be one or two other layers of siding underneath that contractors just left and sided over. The new siding's cost depends on what sits underneath and how much needs to be torn out first.

  • Re-siding a 2,000 sq ft home in vinyl, $6,800 to $20,400
  • A 120 sq ft vinyl section, about seven crew hours
  • Tear-off, house wrap and trim priced as separate lines
  • Sheathing shown to you while the wall is open
  • Old cement shingles tested before anyone cuts one

Squares times the rate, before anyone climbs a ladder

Typical prices per square foot for Omaha jobs. Your quote follows a look at the job.

$6,800 to $20,400

Call (531) 228-4688 for your price

At a glance

Re-side in vinyl, 2,000 sq ft home$6,800 to $20,400
Re-side in fiber cement, same home$10,200 to $25,500
Vinyl, small Omaha job$6.86 to $11.59 per sq ft
Old siding off and hauled$0.70 to $2.00 per sq ft
Crew time, 120 sq ft of vinylAbout 7 labor hours
Omaha contractor licenseClass E or higher

Residential Siding Installation, Repair and Replacement

Each card starts at the wall and works out to the panel, because that is where a siding job goes right or wrong.

  • Pale blue lap boards with a wood-grain texture and butt joints

    Fiber Cement Siding Installation

    Fiber cement siding installation can cost anywhere from $6 to $15 per square foot. Installing the siding on your home can take longer than typical vinyl siding because the boards are heavier and they are slower to cut and install onto the house. The boards typically are installed just primed. Once they're up, a painter needs to come afterwards and paint the entire house. Vinyl and some other sidings come pre-finished and don't need painting.

  • Gray horizontal lap siding around a small window with white trim

    Siding Repair

    Siding repair is pretty common. A typical repair job can run $200 to $1,100. We use a zip tool that unhooks the clips from the row above, so a broken panel can come off without taking the whole wall down. Hopefully we can find a leftover box of siding from the original job, which will be the best way to match the style and color of the existing wall.

  • Green-sided house with dormers, a front porch and a two-car garage

    Vinyl Siding Installation

    In vinyl siding installation, how the siding is installed has a lot to do with how it will look throughout the seasons, especially in the summer. It costs $4 to $12 a square foot, and 120 square feet can take about seven man hours. We recommend nails that sit mid-slot and are not driven in tight. That lets the panel slide a bit, as these panels can move on the freezing days and the hot days. If the nails are tight, this can make the panels bulge into waves on hot days.

  • Three workers on ladders fitting white siding over green sheathing

    Siding Replacement

    In a siding replacement, the real work begins with the tear-off of the old siding. Re-siding a 2,500-square-foot house can cost anywhere from $10,000 to $32,500 for labor and materials. Once the tear-off of the old materials is done, the wood needs to be inspected to make sure there is no rotted wood where leaks have been hitting the side of the house. Then the house gets wrapped before the new siding goes on. The wrap is a sheet behind the siding that keeps water and wind out.

  • Dark gray lap siding meeting a light corner trim, bare trees behind

    Steel Siding

    Steel siding for your home is formed on a machine that will be parked in your driveway. These are long wall panels with no lap joints. There are different gauges of thickness for this steel siding, and the gauge should be agreed upon and written on the bid before any work is done. This style of steel siding is great for walls facing open ground to the west, where the hardest storms of wind, rain and hail hit.

  • Roof corner with red fascia and trim above white lap siding

    Soffit and Fascia Repair

    Soffit and fascia repair on your home is usually needed when water has leaked onto the soffit and fascia boards for many years, typically from a leaking gutter. Over the years this rots the wood, which will need to be replaced. You should always be sure, before any of these wood repairs are done, that the cause of the rot has been permanently fixed. Otherwise, the new wood you put in will only start rotting again over the years.

  • Peeling paint on weathered wood siding beside a window

    Wood Siding Repair

    Wood lap and cedar shakes rot first at the bottom course and under windows, usually from water arriving from above. We cut soft boards back to sound wood, prime every cut end and match the reveal of the old lap. Old laps vary. On an older house the reveal may not be a stock size, and 60% of Omaha's homes were built before 1980.

  • Illustration: Tan vinyl siding below a window, pocked with small hail dents and two chipped panel edges

    Hail Damage Siding Repair

    Hail seldom hits every side, so the wall that faced the storm takes the damage while the others look new. We photograph each hit, the J-channel and the trim with a tape measure in the frame, and label which side of the house it is on. That record is yours to send your insurer. We suggest waiting for the adjuster's visit before any panel comes down.

  • Sage green lap siding next to a brick chimney and a white downspout

    Engineered Wood Siding

    LP SmartSide and other engineered wood siding is a wood product under a paint film. We keep its bottom edge off concrete and its ends clear of roof lines, where standing water would swell the edge. It repaints like wood. Read the maker's warranty before you sign, because an install outside its rules can void it.

Holding a siding bid that says one number?

A single total can hide the tear-off, the house wrap and the trim. Send us the lines you were given and the rough size of the house, and we show you what a full bid would spell out.

Commercial Siding Installation and Repair

Bigger walls, the same questions about what sits behind the panel.

  • Apartment Building Siding

    Multifamily walls run long and tall. Lift access and the order of buildings set the schedule, and tenants want to know which week is theirs. We price by the square for each building and close every elevation before the lift moves on.

  • HOA and Townhome Siding

    Boards want one color. We bid by building and by side, so an HOA can phase the re-side across two or three budget years without mixing panel runs from different production lots.

  • Rental House Siding Repair

    Between tenants, a landlord wants the broken side fixed and nothing more. We quote the damaged run, write down the profile and color for next time, and say plainly when a whole side will match better than a patch.

  • Commercial Metal Siding

    Metal panel walls on shops and warehouses hang on girts, not sheathing. On a repair we match the rib spacing and the gauge. A wrong rib shows from the parking lot.

  • Storefront Siding Repair

    A shop on a busy street needs the work fitted around open hours. We stage the tear-off by section so the entry stays usable, and the sidewalk gets swept for nails before the doors open next morning.

Specialty Siding Services

Smaller jobs behind and around the panels, where one detail settles the price.

  • Volunteers fastening house wrap and trim on a new house wall

    House Wrap and Flashing Repair

    Siding sheds most of the rain, and the wrap behind it handles what gets past. Where a roof meets a wall, a missing kickout flashing sends water down behind the panels to rot the sheathing out of sight. We add the kickout and the window head flashing a wall lacks. Look for a dark streak below the low end of a roof-to-wall joint.

  • Worker in a hard hat fitting foam sheathing board at a house corner

    Insulated Siding and Foam Board

    Foam board under new siding flattens an old wavy wall and adds a layer between the studs and the weather. Insulated vinyl has its foam bonded to the back of the panel. Both add depth, so the casing around each opening gets extended, and we put that trim in the same bid.

  • Front porch with white columns under a gray board and batten gable

    Board and Batten Siding

    Board and batten is a look, not a material. It comes in fiber cement, engineered wood, vinyl and steel, and it often goes on a gable or an entry with lap siding below. Vertical boards need furring or blocking behind them, which we price before the first board goes up.

  • Painter on a ladder rolling paint onto a white wall with a long pole

    Siding Painting for Primed Board

    Primed fiber cement leaves the factory ready for paint, not finished. A painter follows the siding crew, and the paint stage sits on the bid as its own line, so the total you compare is a finished wall. Rub old paint with a finger; chalk on your hand means it has worn through.

  • Older two-story house covered in gray cement shingle siding

    Asbestos Cement Siding Checks

    Gray cement shingles on an older house may contain asbestos. Nebraska's state program is stricter than the federal rule and starts at small quantities, so we ask for a lab test before anyone cuts, drills or pulls one. A firm holding the state's credentials handles removal. We do not.

How a Siding Job Runs

  1. You describe the house by phone. If it sounds like one panel, we say so before anyone drives out.
  2. A ladder walk around all four sides, looking above every stain. The photos are yours.
  3. A bid in lines, with panel squares, tear-off, wrap and trim priced apart.
  4. Tear-off goes one side at a time. You see any soft sheathing before it is cut out.
  5. New wrap and panels close that side, and a magnet sweeps the beds for nails each evening.
  6. A final walk with you, the back of the house included.

Omaha’s Class E Contractor License

Omaha licenses siding contractors under Class E, covering work up to three miles outside its limits. Ask to see it. Nebraska also registers contractors with its Department of Labor.

Hail, Wind and Omaha Siding

On July 31, 2024, gusts of 90 mph were reported east of downtown and 75 mph west of Millard, and that June brought two hail days. Storms start a lot of siding work here.

Before the Adjuster Comes

Take dated photos of each damaged side, then close-ups. Cover any hole that lets rain in, and keep the receipt for that patch, as the state advises.

Read It Before Signing at the Door

The Nebraska Department of Insurance warns that an assignment of benefits hands your claim to a contractor or public adjuster, and can leave you paying the gap between bill and payout.

How Long Siding Work Takes

Job Labor hours What sets the pace
Vinyl, 120 sq ft About 7.3 Channels and openings
Fiber cement, 120 sq ft About 7.2 Board weight, cutting
Steel, 120 sq ft About 7.6 Trim and corners
Vinyl soffit, 125 ft About 3.3 Vents, fascia below
House wrap, 500 sq ft About 1.5 Taping, window laps

Crew hours on an easy-access wall in zip 68102, 2026, with no tear-off. Two or three installers split them.

What Siding Costs in Omaha

Siding Prices by Job

Job Typical range Basis
Vinyl, whole house $6,800 to $20,400 1,700 sq ft of wall
Fiber cement, whole house $10,200 to $25,500 1,700 sq ft of wall
Steel, whole house $14,000 to $32,000 2,000 sq ft home
Vinyl section, Omaha $823 to $1,391 120 sq ft, no tear-off
Old siding off and hauled $0.70 to $2.00 per sq ft
Typical siding repair $200 to $1,100 per job
Soffit and fascia together $9 to $34 per linear foot

The Omaha row is zip 68102 in 2026, with no removal of the old layer; the others are national 2026 figures. A small section runs higher per foot than a whole wall, and the real number comes after a walk around the house.

What Moves the Price

  • Layers coming off. Two old layers double the tear-off and the dump load.
  • The wall behind. Soft sheathing is replaced by the sheet, and nobody can count sheets before the tear-off.
  • Openings and height. Each window takes head flashing and trim, and a two-story gable needs staging.

Two Bids, One House

Lay two far-apart totals line by line. The cheaper one has often left out the tear-off or the wrap, and those come back as change orders.

Years ago, my brother, who lived in a rainy, wet climate, had a siding contractor put new siding on his home. Unfortunately, my brother chose the cheapest route possible, which was a cheap siding of pressed particle board. But after only one rainy season, the siding started swelling from the rain, especially near the joints where two pieces of siding come together. After two seasons, he had to have it all torn off and redone. Luckily, there was a warranty on the siding, so he did not have to pay for this, but he learned a great lesson.

Repair Before Re-Side

If the damage is on one side and the color still matches, a repair buys time. Once panels crack as you bend them, the money goes further on the whole wall.

If it’s your house, we would strongly consider repairing the broken panels on one wall, especially if the rest of the house’s siding is in good shape. This will be much cheaper than re-siding the entire house, especially if the color has not faded.

The wall tells you more than the panel

A cracked panel is the easy part to see. What matters is whether the sheathing behind it stayed dry, and that decides between one section and a whole side.

Siding From Elkhorn Road to the River

Omaha Plains Siding covers Omaha, NE, plus Sarpy County towns from La Vista to Gretna, Blair and Fremont to the north and west, and Council Bluffs across the Missouri.

Douglas County, NE

  • Ralston
  • Bennington
  • Valley

Sarpy County, NE

  • La Vista
  • Papillion
  • Bellevue
  • Springfield
  • Gretna

Pottawattamie County, IA

  • Carter Lake
  • Council Bluffs

Washington County, NE

  • Fort Calhoun
  • Blair

Saunders County, NE

  • Yutan

Cass County, NE

  • Louisville
  • Plattsmouth

Council Bluffs and Carter Lake are in Iowa, where a siding contractor registers with the state under Iowa Code 91C.

The June 12, 2024 hail fell in a narrow strip from Blair through Hanscom Park to Bellevue, with stones 2 to 2.5 inches across.

Siding Questions Omaha Owners Ask, Hail to Tear-Off

Can you put new siding over old siding?

We seldom recommend new siding over old siding. It often doesn't hold firm to the wall. The extra layer makes the wall thicker, so the trim and doors sit back and don't look good.

Does homeowners insurance cover hail damage to siding?

Hail damage coverage depends on how your policy is worded. Always call the insurer first, and don't go by what the contractor says until you find out about your insurance.

Do you need a permit to replace siding in Omaha?

Ask who pulls it before you sign, and phone Omaha's Permits and Inspections desk if the answer is vague. Bellevue, Papillion and the other towns run their own building offices and rules.

How long does siding last on a house?

Vinyl siding can last around 30 to 40 years, while steel siding can last from 40 to 70 years. Cedar can last 20 to 40 years if kept up properly.

Is James Hardie siding worth it in Omaha?

If the homeowner plans on staying in the home for many years, then we believe fiber cement board is worth it. It runs about $3,400 to $5,100 extra, but it will last and look better over the years, much better than vinyl.

Can you replace one piece of vinyl siding?

Yes, we can replace only one or two pieces of vinyl siding. For the new material, you're only looking at about $8 to $60, but the real challenge is matching the same shape and the color.

Does asbestos siding have to be removed?

Asbestos siding does not always have to be removed. Disturbing it is what causes most of the problems. A sample test should be done before any cuts are made.

Can siding be installed in winter?

Yes, siding can be installed in the winter with more care. Cold vinyl becomes brittle and shrinks, so it needs wider gaps at the panel ends.

What does hail damage look like on siding?

Hail damage on vinyl can cause holes and cracks, which can be seen from the yard pretty easily. Metal siding can have round dents that can be seen in low sunlight.

Request a quote

Call (531) 228-4688 and describe the house as you walk around it, or list what you spotted below. A person reads it and rings back.

What you type goes only to the siding crew who would look at the house. Nobody else sees it, and nobody sells it.

Call (531) 228-4688Price my siding